Know where your antenna is. To about a centimetre.
Truepoint works out where your GNSS antenna is from its own data, and hands that position to the timing receiver. Position error stops leaking into your time.

16.7 mm
From an independent survey
3D distance in our bench test. The survey's own uncertainty was 15 mm.
62×
Closer than survey-in
The receiver's own survey-in was 1029.7 mm off in the same test.
~3.3 ns
Per metre of position error
The time error that antenna position error puts into a timing solution.
2 days
Must agree
A coordinate is only used when two separate days match.
Bench test: one unit, 13.2 hours of data, 15 September 2026.
The problem
A metre of position error is 3.3 ns of time error
A timing receiver needs to know exactly where its antenna is. Most get there by averaging their own fixes for a while (survey-in), which stalls at around a metre. Any error in that position goes straight into the time: about 3.3 ns for every metre, and it shifts as the satellites move, so it cannot be calibrated out.
The usual fix is to pay a surveyor to visit each roof, which is slow and costly across a fleet and is a one-off. Nobody notices later if the antenna is moved, knocked or swapped.
How it works
From the timecard’s own data. No surveyor visit.
Recording, solving, quality checks and applying the coordinate are all automatic. You turn it on for a device in Sync Insight and watch the position arrive.
01
Recording
The timecard records its raw satellite measurements every 30 seconds, around the clock, and sends them to Timebeat. The clock keeps running normally while it does.
02
Solving
Once a full day is in, the service combines it with the precise satellite orbits and clocks published by the international GNSS community, and works out where the antenna is to about a centimetre.
03
Agreement
A coordinate is only accepted when two separate days agree within 5 cm, and 3 cm vertically. One bad day cannot slip through, and the spread between days is the stated accuracy.
04
Applied and watched
The timecard fixes its receiver to that position. Sync Insight shows the position and the history of each day's result, and emails you if the antenna appears to move.

Daily checks
If the antenna moves, you hear about it
With Truepoint, each solved day is compared with the reference position. Movement beyond the device’s threshold, 50 mm by default, marks the device as Moved and emails the account. The clock keeps its position until you accept a new baseline.
Sync Insight keeps the position and the history of every day’s result for each device, so a knocked mast or a swapped antenna shows up as a dated event, not as a mystery in your offsets months later.
Two ways to buy
Checked every day, or solved once
Both are priced per device, and each device has its own plan. A Truepoint Survey gives a centimetre position once. Truepoint keeps checking it.
Truepoint
A centimetre position that is checked again every day.
£1,000per device, per month
- First provisional coordinate in about 2 to 3 days, a rapid one in about 6 to 7
- Refined on final products after about 18 days
- Every day's result compared with the reference position
- Email alert if the antenna moves beyond your threshold, 50 mm by default
- Six-month minimum, with the first six months paid up front
Truepoint Survey
One centimetre coordinate, solved once and kept by the device.
£2,000per device, once
- One coordinate per device, solved on final products
- Ready in about 3 weeks, once two days agree
- The device holds the coordinate afterwards
- Not re-checked: no daily results and no movement alerts
- Each Survey you have paid for takes £2,000 off one device's first Truepoint payment
Prices in pounds sterling. Truepoint is rolling out to Sync Insight customers. Talk to us to check your hardware and timing.
Who it’s for
Where every nanosecond in the budget counts, and nobody surveyed the antenna
Telecom and 5G
Phase budgets such as ±1.5 µs end to end (ITU-T G.8271.1) leave little room. A metre of antenna error is about 3.3 ns that varies through the day, spent before the network starts. Surveying thousands of cell-site antennas by hand does not scale.
Finance and trading
Traceability claims under MiFID II RTS 25 and SEC CAT rest on the reference being right. A documented, independently checkable antenna position with a daily history is evidence an auditor can follow.
Data centres and cloud
Rooftop antennas are often fitted by contractors with no survey. The position gets fixed fleet-wide from the devices' own data, and an alert fires if an antenna is moved during building work.
Defence and government
A known, monitored antenna position is part of trusting a timing reference. Unexpected movement of the computed position is flagged automatically rather than found in an audit.
Versus the alternatives
Four ways to get an antenna position. One that keeps checking.
| Alternative | Its limitation | With Truepoint |
|---|---|---|
| Receiver survey-in only | Stalls around a metre: about 3.3 ns of time error that moves with satellite geometry | A centimetre-level position from precise products, measured 16.7 mm from an independent survey |
| Professional site survey | A paid visit per site, a one-off number, and nobody notices if the antenna later moves | A Truepoint Survey gives the number from the device's own data, without a visit. Truepoint re-checks it daily across the fleet |
| In-house, with online PPP tools | Someone has to export raw data, run it, check it and type the result into each receiver by hand | Recording, solving, quality checks and applying the coordinate are all automatic |
| Coordinates from a map or building plan | Metres out, and height is usually a guess | A measured 3D position, including height, checked across independent days |
Specifications
The numbers, with their conditions
| Parameter | Value | Conditions |
|---|---|---|
| Position accuracy, bench test | 16.7 mm 3D | Against an independent survey (15 mm uncertainty). One unit, 13.2 h of data, 15 Sep 2026 |
| Survey-in, same test | 1029.7 mm 3D | The receiver's built-in method that Truepoint replaces |
| Day-to-day repeatability | 1.1 mm | Difference between two separately accepted days on the bench unit, rapid products, Sep 2026 |
| Acceptance rule | Two days agree within 5 cm (3 cm vertical) | The spread between days is the stated accuracy |
| Receiver | u-blox LEA-F9T | Dual-frequency antenna required. Single-band setups are blocked |
| Recording | Every 30 s, about 5.8 MB per device per day | Raw observations sent to Timebeat |
| First coordinate, Truepoint | ~2 to 3 days provisional, ~6 to 7 days rapid | Provisional needs quick first location on. Refined on final products after ~18 days |
| First coordinate, Truepoint Survey | About 3 weeks | Solved on final products only, published about 17 days after each day, and two days must agree |
| Movement alert | 50 mm 3D by default | Configurable per device or group |
| Applied to receiver | 0.1 mm resolution | The receiver is rewritten only when the coordinate moves 1 cm or more |
Good to know
What it does, stated plainly
It measures position, not time
Our test measured how close the position is. Truepoint removes a source of time error worth about 3.3 ns per metre of position error. We do not quote a timing improvement figure.
About a centimetre, not a guarantee
16.7 mm is one bench unit at one site. Results depend on the antenna, its calibration and the sky view.
Ready in days, not instantly
The solve needs full days of data and published satellite products. The portal shows a timeline for each device while it waits.
Compatibility is checked first
Truepoint needs a dual-frequency antenna and the LEA-F9T receiver. The portal checks that the receiver tracks two frequency bands before you turn it on. An uncatalogued antenna model leaves a few centimetres of vertical offset.
Truepoint · part of Sync Insight